all right we're back here it's a brisk morning but there's no wind again we are
getting super lucky with the cold weather coming in without wind usually
those two seem to come with each other but we're gonna go ahead and get going
on this back end wall which first we got to get our porch pier brackets installed
so we can start building this porch once the framing is done then we have it
properly flashed we can bring the steel up and over the corner so that's gonna
be the main goal today look at that brand-new SDS inch and 7/8 the Walt sent
out so of course we're gonna give it a try
pretty much overkill and then Bosch stopped over yesterday to the job site
and brought out these demo bits here look at the tip on those I was always a
Bosch rotary hammer guy but I don't own any box rotary hammer is cordless mine
are all corded sort of this thing holy cow
honestly I don't have any review of this thing I haven't even used it as you can
tell but we're gonna though it's got a soft ramp up adjustable speed
let's go dig some holes Drake what I think I want to like about this is that
most of time when you go ahead and start in with a rotary hammer it bounces all
over the place but this has a really has a slow start up and then it ramps up so
I'm hoping that that takes care of that
honestly I feel like very little to no vibration in my hand
but the weight of the tools is the whole job
I love those Simpson type hd's Simpson you want sponsor me huh you know it
doesn't happen all the time but when it does it makes you proud and what I'm
talking about is when you pour all of your porch piers come back in with a
laser and every one of them
it's the mark I always say if you spend time early and if you work at your
layout when you put the site in everything falls together much easier
and this is another one of those examples we're gonna now be able to cut
all three porch post piers exact our porch post exactly the same I always try
to get our cedar s4s so it's sanded on all four sides almost always comes out
of Boise Cascade there's a big supplier or a supply house really close to me and
they've always got a really nice cedar product it's very clean it's not all
cracked out six by six s4s cedar that's what we like to do our post-and-beam
look on our building we think it sets it off real nice well I'm I'm super
disappointed because I forgot my favorite beam saw you guys have seen me
use it and the tools des vidéos i've used it for the last probably about a
year now that's a super sasquatch I forgot it at home I try not to keep it
the trailer because it is an expensive tool and I don't want it to get ruined
or something set on it or you know get it off I guess I don't want to mess up
the precision of it I've spent a lot of time getting it zeroed in and how I like
it and I don't want it to get hit even
though it sits in that sweet case so I'm having to use my 10 inch chop saw and it
requires me to be very careful and I have to cut halfway through flip it over
get it precisely lined back up and then cut it again and it really sucks
especially when I have to cut my miters here that I'm gonna be cutting for the
the header around the corners I couldn't do it
I had to greg graciously thank you Greg yes awesome headed back to the shop
picked up the beam saw because as you can see this is all I was able to do on
one cut one side of the miter saw I couldn't even get down all the way so
it's only a ten inch and it just didn't have the depth you know so I'd rather
use this anyway we just made the commitment I've got the post we just
stood those up so now we're gonna do is we're gonna cut the beams that go around
so we've got miters out on these two points over here so that's that's the
hardest part you got to go in perfect and this thing does a good job
it's what I ended up doing was I went ahead and took my receiver and I set it
along and right at the top of this post set it and then I used it to transfer
over to these marks here and what that is is if you look that first line is the
top of my post which means that's where my header the bottom of my header is
gonna die in right here and then this line I snapped five and a half inches up
that's the top and that's where I'm gonna run a two by against the wall so I
can support my ceiling and my hip rafters and all that other good stuff is
going to be all based off of that line which will be the top of my header so
now we're able to I'm gonna put a couple blocks just to temporarily mount the
headers where they die into the seat of the wall and we'll get them all mounted
up so I spent time to figure out all my angles calculations figured out what my
degrees where where my purlins ended up on my rafters I got them cut I've got
the locations marked out now everything I did was to Center so I've also got to
always take into account for that so like for this right here the actual
centerline of my purlins is going to look like that going that way and from
this way it'll be something like this but you'll see that when I get up but
these are my two hips what happened was Kyle made a little mistake but it really
is gonna be okay you can see how much bearing I got out here on my post in my
corner column where Greg is but what happened is these are twelve foot two by
twelves and I needed twelve foot four inches so what we're gonna do is we're
gonna put them up there and then I'm gonna cut I've already cut a couple two
by six blocks that I'm gonna laminate to each side that's gonna come out to help
frame in my overhang now I understand that's not you know
Oh perfect but let's be real I'm not perfect
and so this is kind of like the fix on site in a perfect world I would have to
buy 12 16 footers here that I cut down when I did the initial math I don't
think I was thinking about the one foot overhang that I had to account for and I
typically do a purl in on top of my rafter which means I don't need as long
of a rafter because it's actually sunk down into the roof system so I don't
that really makes sense but this is gonna be the top of this 2 by 12 will be
the top plane of my roof where I'm gonna put my sheathing and so with that being
said I ended up meeting a little bit longer 2 by 12 but I think it's gonna
work I'm anxious to put them up on the building and actually see if all of my
math is correct because math never lies the problem is you can do the wrong math
and then it could be wrong so hopefully I didn't just waste a bunch of time now
you can see what we've got going so this was the end of that 2 by 12 that we
actually ran short on and we've got it installed we've got our other face had
done and basically what I've done is I've cut blocks with the appropriate
angle and all I'm gonna do just gonna slide them in running them on
the top of my header that's the beauty is math never lives so we're gonna put
this all together right when I post B's and because this is not a perfect 45
degree since we've got different dimensions so this dimension going back
that way is eight feet but this is only seven foot this is actually offset from
where the corner of the 40s but that's only the hip is offset it will look that
will look appropriate once we get it all done I don't know if that makes sense
there we go rag there we
so is this how I wanted it no I really wanted this two-by-two plane all the way
down perfect but you know we're not in a perfect world but I think it turned out
a lot better than a anytime you do a lot of math and weird angles you never
question all it takes is one mishap
I always like to just throw a bunch of grk screws in here and then I come back
in with some luck 2030
I've got to do now is cut these purlins and these purlins they're what's gonna
go up here on the roof and are gonna frame in from this wall to this wall
that's my framing that I'm gonna sheet kind of like the purlins that are up on
the main roof what I've got to do is they've got a compound angle so as you
can see here they're pitched at a 4-12 to be planed in with the 4:12 pitch of
my roof but then on the end they're also pitched at forty six point eight seven
degrees which if you remember back here I figured that out so this corner this
triangle of my roof is what this is right here and I did all this math
already and it will be the exact same when I flip flop it over here so I just
have to change the angles and this side I have not done yet in here these will
actually carry from one hip to the other and I've dropped down this rafter so
that my 2x4 perrilyn will go right over top of it
so these compound angles are a little bit tough got the chop saw out and you
just got to take them nice and slow so all of the math that I just done was all
based on the centerline of these hip rafters from the wall that's what I got
to do is we've got this 3/4 I'm just gonna mark it at 3/4 and plane it back
this way playing it back this way and this is where my rafters are gonna die
in right here and then we'll use the math up here we've got our snap line
this is the top plane line from our our 2 foot 8 rise down to our fascia line
and really the math is when there you go it's a good example of how if you take
the time to do the math things should work and that's constant
and if you put everything where you're supposed to go should straighten
everything out as well we'll get some hangers over here we remember we did
that ledger two by twelve over here that's what everything's fascinating
into so we got nice and solid we'll get some hangers and then you can see here
how this two by twelve is dropped that's for a two by four plane to go over top
of it we'll hit some 60s straight down and then it will plane right into our
hip rafters all right were we made our marks so the major takeaway from this
video guys is use math especially when making complicated dimensional cuts on a
project like a hip porch and we're gonna go ahead and break this up because the
next video will all be about I guess the finishes will sheet it will get the
steel on it will do the trim details but it's just too much to put all into one
video without sacrificing and I figure you guys would rather have more content
than not enough so we'll look for you on the next video make sure you subscribe
hit that thumbs up share these videos with your friends I really appreciate
the support and that definitely gives me the encouragement to keep going but for
now we'll catch you guys on the next video
and stay tuned later